Yaesu Illuminator G-450/650 3 LED Board

Our newest Ham Supply product, the Yaesu Illuminator G-450/650 3 LED Board is out of research & development and is now offered to the radio community at large.  Confirmed fit in Yaesu G-450 and G-650 series rotor controllers.

In stock, ships now!

Are you tired of your dark Yaesu Rotor Controller because the pesky non-serviceable, super high-intensity “fuse” style light bulb burned out? Frustrated from trying to repair or replace it, let alone worn out from all you needed to do just to access the stock bulb?  When you finally do access the bulb you’ll find out you can’t buy the bulb?  What then?  If it’s anything like a couple of my Yaesu Rotor control boxes (right before they decided they didn’t want to light anymore) they actually deformed my plastic corner dial ring and housing.  That’s some real heat nobody wants in their rotor controller!

Our Assembled & Tested Yaesu Illuminator G-450/650 3 LED board gives you all the light you need, even in daylight!  The Yaesu Illuminator G-450/650 3 LED board comes preassembled, all you do is mount the small printed circuit board and connect two wires.  Our simple step by step instructions are easy to follow.  The best part is you don’t need to be an electronic technician; a Phillips screwdriver, a pair of side cutters and about 20 minutes and you’re done!  In most cases (if not all) there are no internal plugs to connect/reconnect – the only plug you need to disconnect/reconnect is the power cord!  No printed circuit board assembly either as we’ve done that for you!

We have targeted the design of our Ham Supply Yaesu Illuminator G-450/650 3 LED board for low cost and simplicity, yet we wanted it to be very, very effective.  Mission accomplished!

I am not a photographer (I’m a DXer), and they say it’s always hard to photograph “light” – but here’s a few side by side comparisons below.  I think you can see what the Yaesu Illuminator G-450/650 3 LED board can do for your Yaesu Rotor Controller.

This photo taken in broad daylight – what a difference!

The Ham Supply Yaesu Illuminator G-450/650 3 LED board fits Yaesu G-450 and G-650 series rotor controllers.

At $22.95 Assembled & tested we think you’ll be quite pleased with our design, placement and finished product.  The Yaesu Illuminator G-450/650 3 LED board comes with all necessary hardware, wiring, installation manual and our assembled & tested printed circuit board – all you do is install it!

Yaesu Illuminator G-450/650 3 LED board Documents

Ham Supply Yaesu Illuminator G-450/650 Installation Instructions

For Yaesu G-800/1000/2700 and 2800 controllers see our Yaesu Illuminator G-800/1000/2700/2800 here.

Yaesu Rotor Accessories

Yaesu RotorCard DXA:  Computer control RS-232/USB point & shoot rotor control board (DXA/DXC series rotors)
Yaesu RotorCard SDX:  Computer control RS-232/USB point & shoot rotor control board (SDX series rotors)
USB/RS232 Converter Cable:  3′ with Hex Nuts
Yaesu Illuminator G-800/1000/2700/2800:  3 LED board for Yaesu 800/1000/2700/2800 series rotor controllers
Yaesu Illuminator G-450/650: 3 LED board for G-450 and G-650 series rotor controllers
DXA/C-6′ Mini-DIN 6′ Cable:  Front panel transceiver control of your Yaesu DXA/DXC series rotor controller
Yaesu 7 Pin Rotor Plug: Connector, G-450, G-550, G-650, G-800DXA, G-1000DXA, G-2700DXA, G-2800DXA and G-5500 rotators
Yaesu 6 Pin Rotor Plug: Connector, G-450XL, G-800S, G-800SDX, G-1000SDX, G-2700SDX and G2800SDX rotators

Pricing and Ordering

Yaesu Illuminator G-450/650 3 LED Board:  $26.95  $23.95